</para>
</formalpara>
<para>
- If you want to test the experimental HVM support
+ If you want to test the HVM support
with Ganeti and want VNC access to the console of your
instances, set the following two entries in
<filename>/etc/xen/xend-config.sxp</filename>:
</para>
<para>
- Supported DRBD versions: the <literal>0.7</literal> series
- <emphasis role="strong">or</emphasis>
- <literal>8.0.7</literal>. It's recommended to have at least
- version <literal>0.7.24</literal> if you use
- <command>udev</command> since older versions have a bug
- related to device discovery which can be triggered in cases of
- hard drive failure.
+ Supported DRBD versions: <literal>8.0.x</literal>.
+ It's recommended to have at least version <literal>8.0.7</literal>.
</para>
<para>
you have the DRBD utils installed and the module in your
kernel you're fine. Please check that your system is
configured to load the module at every boot, and that it
- passes the following option to the module (for
- <literal>0.7.x</literal>:
- <computeroutput>minor_count=64</computeroutput> (this will
- allow you to use up to 32 instances per node) or for
- <literal>8.0.x</literal> you can use up to
- <constant>255</constant>
- (i.e. <computeroutput>minor_count=255</computeroutput>, but
- for most clusters <constant>128</constant> should be enough).
+ passes the following option to the module
+ <computeroutput>minor_count=255</computeroutput>. This will
+ allow you to use up to 128 instances per node (for most clusters
+ <constant>128 </constant> should be enough, though).
</para>
<formalpara><title>Debian</title>
<para>
- You can just install (build) the DRBD 0.7 module with the
+ You can just install (build) the DRBD 8.0.x module with the
following commands (make sure you are running the Xen
kernel):
</para>
</formalpara>
<screen>
-apt-get install drbd0.7-module-source drbd0.7-utils
-m-a update
-m-a a-i drbd0.7
-echo drbd minor_count=64 >> /etc/modules
-modprobe drbd minor_count=64
- </screen>
- <para>
- or for using DRBD <literal>8.x</literal> from the etch
- backports (note: you need at least 8.0.7, older version have
- a bug that breaks ganeti's usage of drbd):
- </para>
- <screen>
-apt-get install -t etch-backports drbd8-module-source drbd8-utils
+apt-get install -t etch-backports drbd8-source drbd8-utils
m-a update
m-a a-i drbd8
echo drbd minor_count=128 >> /etc/modules
+depmod -a
modprobe drbd minor_count=128
</screen>
<para>
It is also recommended that you comment out the default
- resources in the <filename>/etc/dbrd.conf</filename> file, so
+ resources in the <filename>/etc/drbd.conf</filename> file, so
that the init script doesn't try to configure any drbd
devices. You can do this by prefixing all
<literal>resource</literal> lines in the file with the keyword
(part of iputils package)</simpara>
</listitem>
<listitem>
- <simpara><ulink
- url="http://www.kernel.org/pub/linux/utils/raid/mdadm/">mdadm</ulink>
- (Linux Software Raid tools)</simpara>
- </listitem>
- <listitem>
<simpara><ulink url="http://www.python.org">Python 2.4</ulink></simpara>
</listitem>
<listitem>
- <simpara><ulink url="http://twistedmatrix.com/">Python
- Twisted library</ulink> - the core library is
- enough</simpara>
- </listitem>
- <listitem>
<simpara><ulink
url="http://pyopenssl.sourceforge.net/">Python OpenSSL
bindings</ulink></simpara>
</formalpara>
<screen>
# apt-get install lvm2 ssh bridge-utils iproute iputils-arping \
- python2.4 python-twisted-core python-pyopenssl openssl \
- mdadm python-pyparsing python-simplejson
+ python2.4 python-pyopenssl openssl python-pyparsing python-simplejson
</screen>
</sect2>
</para>
<screen>
-tar xvzf ganeti-1.2.2.tar.gz
-cd ganeti-1.2.2
+tar xvzf ganeti-@GANETI_VERSION@.tar.gz
+cd ganeti-@GANETI_VERSION@
./configure --localstatedir=/var --sysconfdir=/etc
make
make install
nodes names for a multi-node cluster. In general the best
choice is to have a unique name for a cluster, even if it
consists of only one machine, as you will be able to expand it
- later without any problems.
+ later without any problems. Please note that the hostname used
+ for this must resolve to an IP address reserved exclusively
+ for this purpose.
</para>
<para>
To set up the cluster as an HVM cluster, use the
<option>--hypervisor=xen-hvm3.1</option> option to use
the Xen 3.1 HVM hypervisor. Note that with the
- experimental HVM support, you will only be able to create
+ HVM support, you will only be able to create
HVM instances in a cluster set to this hypervisor type. Mixed
PVM/HVM clusters are not supported by the Ganeti 1.2
- experimental HVM support. You will also need to create the VNC
+ HVM support. You will also need to create the VNC
cluster password file
<filename>/etc/ganeti/vnc-cluster-password</filename>
which contains one line with the default VNC password for the
- cluster. Finally, you need to provide an installation ISO
- image for HVM instance which will not only be mapped to the
- first CDROM of the instance, but which the instance will also
- boot from. This ISO image is expected at
- <filename>/srv/ganeti/iso/hvm-install.iso</filename>.
+ cluster.
</para>
<para>
This step shows how to setup a virtual instance with either
non-mirrored disks (<computeroutput>plain</computeroutput>) or
with network mirrored disks
- (<computeroutput>remote_raid1</computeroutput> for drbd 0.7
- and <computeroutput>drbd</computeroutput> for drbd 8.x). All
+ (<computeroutput>drbd</computeroutput>). All
commands need to be executed on the Ganeti master node (the
one on which <computeroutput>gnt-cluster init</computeroutput>
was run). Verify that the OS scripts are present on all
<para>
To create a network mirrored instance, change the argument to
the <option>-t</option> option from <literal>plain</literal>
- to <literal>remote_raid1</literal> (drbd 0.7) or
- <literal>drbd</literal> (drbd 8.0) and specify the node on
+ to <literal>drbd</literal> and specify the node on
which the mirror should reside with the second value of the
<option>--node</option> option, like this:
</para>
<screen>
-# gnt-instance add -t remote_raid1 -n node1:node2 -o debian-etch instance2
+# gnt-instance add -t drbd -n node1:node2 -o debian-etch instance2
* creating instance disks...
adding instance instance2 to cluster config
Waiting for instance instance1 to sync disks.
<para>
To failover an instance to its secondary node (only possible
- in <literal>remote_raid1</literal> or <literal>drbd</literal>
- disk templates), use <computeroutput>gnt-instance failover
+ with <literal>drbd</literal> disk templates), use
+ <computeroutput>gnt-instance failover
<replaceable>INSTANCENAME</replaceable></computeroutput>.
</para>
projects / ganeti-local / blobdiff