Archipelago » qemu

/*

 * Intel XScale PXA255/270 MultiMediaCard/SD/SDIO Controller emulation.

 *

 * Copyright (c) 2006 Openedhand Ltd.

 * Written by Andrzej Zaborowski <balrog@zabor.org>

 *

 * This code is licensed under the GPLv2.

 *

 * Contributions after 2012-01-13 are licensed under the terms of the

 * GNU GPL, version 2 or (at your option) any later version.

 */

#include "hw.h"

#include "pxa.h"

#include "sd.h"

#include "qdev.h"

struct PXA2xxMMCIState {

    MemoryRegion iomem;

    qemu_irq irq;

    qemu_irq rx_dma;

    qemu_irq tx_dma;

    SDState *card;

    uint32_t status;

    uint32_t clkrt;

    uint32_t spi;

    uint32_t cmdat;

    uint32_t resp_tout;

    uint32_t read_tout;

    int blklen;

    int numblk;

    uint32_t intmask;

    uint32_t intreq;

    int cmd;

    uint32_t arg;

    int active;

    int bytesleft;

    uint8_t tx_fifo[64];

    int tx_start;

    int tx_len;

    uint8_t rx_fifo[32];

    int rx_start;

    int rx_len;

    uint16_t resp_fifo[9];

    int resp_len;

    int cmdreq;

    int ac_width;

};

#define MMC_STRPCL        0x00        /* MMC Clock Start/Stop register */

#define MMC_STAT        0x04        /* MMC Status register */

#define MMC_CLKRT        0x08        /* MMC Clock Rate register */

#define MMC_SPI                0x0c        /* MMC SPI Mode register */

#define MMC_CMDAT        0x10        /* MMC Command/Data register */

#define MMC_RESTO        0x14        /* MMC Response Time-Out register */

#define MMC_RDTO        0x18        /* MMC Read Time-Out register */

#define MMC_BLKLEN        0x1c        /* MMC Block Length register */

#define MMC_NUMBLK        0x20        /* MMC Number of Blocks register */

#define MMC_PRTBUF        0x24        /* MMC Buffer Partly Full register */

#define MMC_I_MASK        0x28        /* MMC Interrupt Mask register */

#define MMC_I_REG        0x2c        /* MMC Interrupt Request register */

#define MMC_CMD                0x30        /* MMC Command register */

#define MMC_ARGH        0x34        /* MMC Argument High register */

#define MMC_ARGL        0x38        /* MMC Argument Low register */

#define MMC_RES                0x3c        /* MMC Response FIFO */

#define MMC_RXFIFO        0x40        /* MMC Receive FIFO */

#define MMC_TXFIFO        0x44        /* MMC Transmit FIFO */

#define MMC_RDWAIT        0x48        /* MMC RD_WAIT register */

#define MMC_BLKS_REM        0x4c        /* MMC Blocks Remaining register */

/* Bitfield masks */

#define STRPCL_STOP_CLK        (1 << 0)

#define STRPCL_STRT_CLK        (1 << 1)

#define STAT_TOUT_RES        (1 << 1)

#define STAT_CLK_EN        (1 << 8)

#define STAT_DATA_DONE        (1 << 11)

#define STAT_PRG_DONE        (1 << 12)

#define STAT_END_CMDRES        (1 << 13)

#define SPI_SPI_MODE        (1 << 0)

#define CMDAT_RES_TYPE        (3 << 0)

#define CMDAT_DATA_EN        (1 << 2)

#define CMDAT_WR_RD        (1 << 3)

#define CMDAT_DMA_EN        (1 << 7)

#define CMDAT_STOP_TRAN        (1 << 10)

#define INT_DATA_DONE        (1 << 0)

#define INT_PRG_DONE        (1 << 1)

#define INT_END_CMD        (1 << 2)

#define INT_STOP_CMD        (1 << 3)

#define INT_CLK_OFF        (1 << 4)

#define INT_RXFIFO_REQ        (1 << 5)

#define INT_TXFIFO_REQ        (1 << 6)

#define INT_TINT        (1 << 7)

#define INT_DAT_ERR        (1 << 8)

#define INT_RES_ERR        (1 << 9)

#define INT_RD_STALLED        (1 << 10)

#define INT_SDIO_INT        (1 << 11)

#define INT_SDIO_SACK        (1 << 12)

#define PRTBUF_PRT_BUF        (1 << 0)

/* Route internal interrupt lines to the global IC and DMA */

static void pxa2xx_mmci_int_update(PXA2xxMMCIState *s)

{

    uint32_t mask = s->intmask;

    if (s->cmdat & CMDAT_DMA_EN) {

        mask |= INT_RXFIFO_REQ | INT_TXFIFO_REQ;

        qemu_set_irq(s->rx_dma, !!(s->intreq & INT_RXFIFO_REQ));

        qemu_set_irq(s->tx_dma, !!(s->intreq & INT_TXFIFO_REQ));

    }

    qemu_set_irq(s->irq, !!(s->intreq & ~mask));

}

static void pxa2xx_mmci_fifo_update(PXA2xxMMCIState *s)

{

    if (!s->active)

        return;

    if (s->cmdat & CMDAT_WR_RD) {

        while (s->bytesleft && s->tx_len) {

            sd_write_data(s->card, s->tx_fifo[s->tx_start ++]);

            s->tx_start &= 0x1f;

            s->tx_len --;

            s->bytesleft --;

        }

        if (s->bytesleft)

            s->intreq |= INT_TXFIFO_REQ;

    } else

        while (s->bytesleft && s->rx_len < 32) {

            s->rx_fifo[(s->rx_start + (s->rx_len ++)) & 0x1f] =

                sd_read_data(s->card);

            s->bytesleft --;

            s->intreq |= INT_RXFIFO_REQ;

        }

    if (!s->bytesleft) {

        s->active = 0;

        s->intreq |= INT_DATA_DONE;

        s->status |= STAT_DATA_DONE;

        if (s->cmdat & CMDAT_WR_RD) {

            s->intreq |= INT_PRG_DONE;

            s->status |= STAT_PRG_DONE;

        }

    }

    pxa2xx_mmci_int_update(s);

}

static void pxa2xx_mmci_wakequeues(PXA2xxMMCIState *s)

{

    int rsplen, i;

    SDRequest request;

    uint8_t response[16];

    s->active = 1;

    s->rx_len = 0;

    s->tx_len = 0;

    s->cmdreq = 0;

    request.cmd = s->cmd;

    request.arg = s->arg;

    request.crc = 0;        /* FIXME */

    rsplen = sd_do_command(s->card, &request, response);

    s->intreq |= INT_END_CMD;

    memset(s->resp_fifo, 0, sizeof(s->resp_fifo));

    switch (s->cmdat & CMDAT_RES_TYPE) {

#define PXAMMCI_RESP(wd, value0, value1)        \

        s->resp_fifo[(wd) + 0] |= (value0);        \

        s->resp_fifo[(wd) + 1] |= (value1) << 8;

    case 0:        /* No response */

        goto complete;

    case 1:        /* R1, R4, R5 or R6 */

        if (rsplen < 4)

            goto timeout;

        goto complete;

    case 2:        /* R2 */

        if (rsplen < 16)

            goto timeout;

        goto complete;

    case 3:        /* R3 */

        if (rsplen < 4)

            goto timeout;

        goto complete;

    complete:

        for (i = 0; rsplen > 0; i ++, rsplen -= 2) {

            PXAMMCI_RESP(i, response[i * 2], response[i * 2 + 1]);

        }

        s->status |= STAT_END_CMDRES;

        if (!(s->cmdat & CMDAT_DATA_EN))

            s->active = 0;

        else

            s->bytesleft = s->numblk * s->blklen;

        s->resp_len = 0;

        break;

    timeout:

        s->active = 0;

        s->status |= STAT_TOUT_RES;

        break;

    }

    pxa2xx_mmci_fifo_update(s);

}

static uint32_t pxa2xx_mmci_read(void *opaque, target_phys_addr_t offset)

{

    PXA2xxMMCIState *s = (PXA2xxMMCIState *) opaque;

    uint32_t ret;

    switch (offset) {

    case MMC_STRPCL:

        return 0;

    case MMC_STAT:

        return s->status;

    case MMC_CLKRT:

        return s->clkrt;

    case MMC_SPI:

        return s->spi;

    case MMC_CMDAT:

        return s->cmdat;

    case MMC_RESTO:

        return s->resp_tout;

    case MMC_RDTO:

        return s->read_tout;

    case MMC_BLKLEN:

        return s->blklen;

    case MMC_NUMBLK:

        return s->numblk;

    case MMC_PRTBUF:

        return 0;

    case MMC_I_MASK:

        return s->intmask;

    case MMC_I_REG:

        return s->intreq;

    case MMC_CMD:

        return s->cmd | 0x40;

    case MMC_ARGH:

        return s->arg >> 16;

    case MMC_ARGL:

        return s->arg & 0xffff;

    case MMC_RES:

        if (s->resp_len < 9)

            return s->resp_fifo[s->resp_len ++];

        return 0;

    case MMC_RXFIFO:

        ret = 0;

        while (s->ac_width -- && s->rx_len) {

            ret |= s->rx_fifo[s->rx_start ++] << (s->ac_width << 3);

            s->rx_start &= 0x1f;

            s->rx_len --;

        }

        s->intreq &= ~INT_RXFIFO_REQ;

        pxa2xx_mmci_fifo_update(s);

        return ret;

    case MMC_RDWAIT:

        return 0;

    case MMC_BLKS_REM:

        return s->numblk;

    default:

        hw_error("%s: Bad offset " REG_FMT "\n", __FUNCTION__, offset);

    }

    return 0;

}

static void pxa2xx_mmci_write(void *opaque,

                target_phys_addr_t offset, uint32_t value)

{

    PXA2xxMMCIState *s = (PXA2xxMMCIState *) opaque;

    switch (offset) {

    case MMC_STRPCL:

        if (value & STRPCL_STRT_CLK) {

            s->status |= STAT_CLK_EN;

            s->intreq &= ~INT_CLK_OFF;

            if (s->cmdreq && !(s->cmdat & CMDAT_STOP_TRAN)) {

                s->status &= STAT_CLK_EN;

                pxa2xx_mmci_wakequeues(s);

            }

        }

        if (value & STRPCL_STOP_CLK) {

            s->status &= ~STAT_CLK_EN;

            s->intreq |= INT_CLK_OFF;

            s->active = 0;

        }

        pxa2xx_mmci_int_update(s);

        break;

    case MMC_CLKRT:

        s->clkrt = value & 7;

        break;

    case MMC_SPI:

        s->spi = value & 0xf;

        if (value & SPI_SPI_MODE)

            printf("%s: attempted to use card in SPI mode\n", __FUNCTION__);

        break;

    case MMC_CMDAT:

        s->cmdat = value & 0x3dff;

        s->active = 0;

        s->cmdreq = 1;

        if (!(value & CMDAT_STOP_TRAN)) {

            s->status &= STAT_CLK_EN;

            if (s->status & STAT_CLK_EN)

                pxa2xx_mmci_wakequeues(s);

        }

        pxa2xx_mmci_int_update(s);

        break;

    case MMC_RESTO:

        s->resp_tout = value & 0x7f;

        break;

    case MMC_RDTO:

        s->read_tout = value & 0xffff;

        break;

    case MMC_BLKLEN:

        s->blklen = value & 0xfff;

        break;

    case MMC_NUMBLK:

        s->numblk = value & 0xffff;

        break;

    case MMC_PRTBUF:

        if (value & PRTBUF_PRT_BUF) {

            s->tx_start ^= 32;

            s->tx_len = 0;

        }

        pxa2xx_mmci_fifo_update(s);

        break;

    case MMC_I_MASK:

        s->intmask = value & 0x1fff;

        pxa2xx_mmci_int_update(s);

        break;

    case MMC_CMD:

        s->cmd = value & 0x3f;

        break;

    case MMC_ARGH:

        s->arg &= 0x0000ffff;

        s->arg |= value << 16;

        break;

    case MMC_ARGL:

        s->arg &= 0xffff0000;

        s->arg |= value & 0x0000ffff;

        break;

    case MMC_TXFIFO:

        while (s->ac_width -- && s->tx_len < 0x20)

            s->tx_fifo[(s->tx_start + (s->tx_len ++)) & 0x1f] =

                    (value >> (s->ac_width << 3)) & 0xff;

        s->intreq &= ~INT_TXFIFO_REQ;

        pxa2xx_mmci_fifo_update(s);

        break;

    case MMC_RDWAIT:

    case MMC_BLKS_REM:

        break;

    default:

        hw_error("%s: Bad offset " REG_FMT "\n", __FUNCTION__, offset);

    }

}

static uint32_t pxa2xx_mmci_readb(void *opaque, target_phys_addr_t offset)

{

    PXA2xxMMCIState *s = (PXA2xxMMCIState *) opaque;

    s->ac_width = 1;

    return pxa2xx_mmci_read(opaque, offset);

}

static uint32_t pxa2xx_mmci_readh(void *opaque, target_phys_addr_t offset)

{

    PXA2xxMMCIState *s = (PXA2xxMMCIState *) opaque;

    s->ac_width = 2;

    return pxa2xx_mmci_read(opaque, offset);

}

static uint32_t pxa2xx_mmci_readw(void *opaque, target_phys_addr_t offset)

{

    PXA2xxMMCIState *s = (PXA2xxMMCIState *) opaque;

    s->ac_width = 4;

    return pxa2xx_mmci_read(opaque, offset);

}

static void pxa2xx_mmci_writeb(void *opaque,

                target_phys_addr_t offset, uint32_t value)

{

    PXA2xxMMCIState *s = (PXA2xxMMCIState *) opaque;

    s->ac_width = 1;

    pxa2xx_mmci_write(opaque, offset, value);

}

static void pxa2xx_mmci_writeh(void *opaque,

                target_phys_addr_t offset, uint32_t value)

{

    PXA2xxMMCIState *s = (PXA2xxMMCIState *) opaque;

    s->ac_width = 2;

    pxa2xx_mmci_write(opaque, offset, value);

}

static void pxa2xx_mmci_writew(void *opaque,

                target_phys_addr_t offset, uint32_t value)

{

    PXA2xxMMCIState *s = (PXA2xxMMCIState *) opaque;

    s->ac_width = 4;

    pxa2xx_mmci_write(opaque, offset, value);

}

static const MemoryRegionOps pxa2xx_mmci_ops = {

    .old_mmio = {

        .read = { pxa2xx_mmci_readb,

                  pxa2xx_mmci_readh,

                  pxa2xx_mmci_readw, },

        .write = { pxa2xx_mmci_writeb,

                   pxa2xx_mmci_writeh,

                   pxa2xx_mmci_writew, },

    },

    .endianness = DEVICE_NATIVE_ENDIAN,

};

static void pxa2xx_mmci_save(QEMUFile *f, void *opaque)

{

    PXA2xxMMCIState *s = (PXA2xxMMCIState *) opaque;

    int i;

    qemu_put_be32s(f, &s->status);

    qemu_put_be32s(f, &s->clkrt);

    qemu_put_be32s(f, &s->spi);

    qemu_put_be32s(f, &s->cmdat);

    qemu_put_be32s(f, &s->resp_tout);

    qemu_put_be32s(f, &s->read_tout);

    qemu_put_be32(f, s->blklen);

    qemu_put_be32(f, s->numblk);

    qemu_put_be32s(f, &s->intmask);

    qemu_put_be32s(f, &s->intreq);

    qemu_put_be32(f, s->cmd);

    qemu_put_be32s(f, &s->arg);

    qemu_put_be32(f, s->cmdreq);

    qemu_put_be32(f, s->active);

    qemu_put_be32(f, s->bytesleft);

    qemu_put_byte(f, s->tx_len);

    for (i = 0; i < s->tx_len; i ++)

        qemu_put_byte(f, s->tx_fifo[(s->tx_start + i) & 63]);

    qemu_put_byte(f, s->rx_len);

    for (i = 0; i < s->rx_len; i ++)

        qemu_put_byte(f, s->rx_fifo[(s->rx_start + i) & 31]);

    qemu_put_byte(f, s->resp_len);

    for (i = s->resp_len; i < 9; i ++)

        qemu_put_be16s(f, &s->resp_fifo[i]);

}

static int pxa2xx_mmci_load(QEMUFile *f, void *opaque, int version_id)

{

    PXA2xxMMCIState *s = (PXA2xxMMCIState *) opaque;

    int i;

    qemu_get_be32s(f, &s->status);

    qemu_get_be32s(f, &s->clkrt);

    qemu_get_be32s(f, &s->spi);

    qemu_get_be32s(f, &s->cmdat);

    qemu_get_be32s(f, &s->resp_tout);

    qemu_get_be32s(f, &s->read_tout);

    s->blklen = qemu_get_be32(f);

    s->numblk = qemu_get_be32(f);

    qemu_get_be32s(f, &s->intmask);

    qemu_get_be32s(f, &s->intreq);

    s->cmd = qemu_get_be32(f);

    qemu_get_be32s(f, &s->arg);

    s->cmdreq = qemu_get_be32(f);

    s->active = qemu_get_be32(f);

    s->bytesleft = qemu_get_be32(f);

    s->tx_len = qemu_get_byte(f);

    s->tx_start = 0;

    if (s->tx_len >= sizeof(s->tx_fifo) || s->tx_len < 0)

        return -EINVAL;

    for (i = 0; i < s->tx_len; i ++)

        s->tx_fifo[i] = qemu_get_byte(f);

    s->rx_len = qemu_get_byte(f);

    s->rx_start = 0;

    if (s->rx_len >= sizeof(s->rx_fifo) || s->rx_len < 0)

        return -EINVAL;

    for (i = 0; i < s->rx_len; i ++)

        s->rx_fifo[i] = qemu_get_byte(f);

    s->resp_len = qemu_get_byte(f);

    if (s->resp_len > 9 || s->resp_len < 0)

        return -EINVAL;

    for (i = s->resp_len; i < 9; i ++)

         qemu_get_be16s(f, &s->resp_fifo[i]);

    return 0;

}

PXA2xxMMCIState *pxa2xx_mmci_init(MemoryRegion *sysmem,

                target_phys_addr_t base,

                BlockDriverState *bd, qemu_irq irq,

                qemu_irq rx_dma, qemu_irq tx_dma)

{

    PXA2xxMMCIState *s;

    s = (PXA2xxMMCIState *) g_malloc0(sizeof(PXA2xxMMCIState));

    s->irq = irq;

    s->rx_dma = rx_dma;

    s->tx_dma = tx_dma;

    memory_region_init_io(&s->iomem, &pxa2xx_mmci_ops, s,

                          "pxa2xx-mmci", 0x00100000);

    memory_region_add_subregion(sysmem, base, &s->iomem);

    /* Instantiate the actual storage */

    s->card = sd_init(bd, 0);

    register_savevm(NULL, "pxa2xx_mmci", 0, 0,

                    pxa2xx_mmci_save, pxa2xx_mmci_load, s);

    return s;

}

void pxa2xx_mmci_handlers(PXA2xxMMCIState *s, qemu_irq readonly,

                qemu_irq coverswitch)

{

    sd_set_cb(s->card, readonly, coverswitch);

}